TECHNICAL ISO/TR REPORT 15599 First edition 2002-10-01 Digital codification of dental laboratory procedures Codification numérique des procédures au laboratoire dentaire Reference number ISO/TR 15599:2002(E) ISO @ ISO 2002 ISO/TR 15599:2002(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The IsO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by isO member bodies. In the unlikely event @ISO2002 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland ii @Iso2002-All rights reserved ISO/TR15599:2002(E) Contents Page Foreword Introductiol Scope 2 Normative references 3 Principle 4 Syntax... 4.1 Software opening file line. 4.2 Dentist's identification code line. 4.3 Laboratoryidentificationcodeline 4.4 Codelinefortheidentificationofacustom-mademedicaldevice 4.5 Code line for the description and site of the medical device .. 4.6 Identification and origin of the device constituent materials. 4.7 Optional code line for the identification of missing tooth/teeth to be replaced in individual prostheses.. 5 Descriptionsanddefinitionsof codes. 5.1 Codes for dental laboratory procedures.. 5.2 Codes for materials (see ISO/TR 13668) ... 5.3 Codes for laboratory steps (see ISO/TR 13668). 6 Classification of dental metals and alloys. Classification of non-metallic materials . 9 7.1 Ceramic codes.. 7.2 Polymer codes 10 Annex A (informative) cosI (from ISO/TR 13668:1998, annex A). 11 Annex B (informative) Explanation Bibliography 5 @ Is0 2002 - All rights reserved ili ISO/TR15599:2002(E) Foreword liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Internationa Standard requires approval by at least 75 % of the member bodies casting a vote. In exceptional circumstances, when a technical committee has collected data of a different kind from that which is anddoesnothavetoberevieweduntilthedataitprovidesareconsideredtobenolongervalidoruseful. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO/TR 15599 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommittee SC 3, Terminology Annexes A and B of this Technical Report are for information only. iv @ ISO 2002 - All rights reserved ISO/TR 15599:2002(E) Introduction codes of oro-dental health status and interventions (COsl), to introduce the advantages of standardization into the procedures of communication between the dental surgery (dental office, in the USA) and the dental laboratory. Provisionally, the country code used in the examples herein is that of the in