ISO/IEC INTERNATIONAL STANDARD 14165-114 First edition 2005-04 Information technology - Fibre Channel : Part 114: 100 MB/s balanced copper physical interface (FC-100-DF-EL-S) IEC ISO Reference number ISO/IEC 14165-114:2005(E) Copyright International Organization for Standardization ted without license from IHS Not for Resale maaaiandardizato orneworkingmitedwithout licene fromH Not for Resale ISO/IEC INTERNATIONAL STANDARD 14165-114 First edition 2005-04 Information technology - Fibre Channel . Part 114: 10o MB/s balanced copper physical interface (FC-100-DF-EL-S) @ISO/IEC 2005 ISO/IEC Copyright Office · Case postale 56 · CH-1211 Geneve 20 · Switzerland H IEC PRICE CODE ISO Forprice,seecurrentcatalogue Copyright International Organization for Standardization itted without license from IHS Not for Resale 2 14165-114 @ ISO/IEC:2005(E) CONTENTS FOREWORD. .5 INTRODUCTION.. Scope. 2 Normative references 3 Definitions, symbols and abbreviations... 3.1 Definitions. 3.2 Symbols 3.3 Abbreviations 4 MAC interface 4.1 General. 4.2 Overview 4.3 Detailed specification.. 10 4.3.1 RD<7:0> received data 10 4.3.2 RV receive valid. 10 4.3.3 RE receive error..... 10 4.3.4 RCLK receive clock.. 10 4.3.5 TD<7:0> transmit data.. 10 4.3.6 TV transmit valid .. 4.3.7 TE transmit error.. 4.3.8 TCLK transmit clock. 4.3.9 DC characteristics... 4.3.10 MAC characteristics 4.3.11 MAC, GMIl and MII interfaces. 4.4 Testing. 12 4.5 Data stream. 4.6 Service control functions. 12 4.7 Timers... 4.8 Delay requirements. 13 4.9 Reset 5 Operation 13 5.1 Detail of the physical interfaces 13 5.2 Signalling .. 5.3 Frame format. 14 5.4 Functions at the MAC interface 6 Coding 6.1 15 6.2 Receive status OK 6.3 Errors. 15 6.4 PHY control.. 15 6.5 Bit error rate.. Test. 7.1 General. 7.2 Tests. 16 7.3 Fixtures. 16 7.4 Interoperability compliance points 16 8 Transmitter signal. 16 Copyright International Organization for Standardization ted without license from IHS Not for Resale 14165-114@ISO/IEC:2005(E) - 3 - 8.1 General. 16 8.2 Differential output voltage and accuracy. 16 8.3 Scrambling ... 16 8.4 Transmit eye diagram .. 17 8.5 Jitter... 9 Receiver signal.. 9.1 General. 18 9.2 Differential input voltage and accuracy 18 9.3 Descrambling .... 9.4 Receive eye diagram.. 10 Electrical and mechanical requirements . 19 10.1 lsolation .... 19 10.2 Clock frequency.... 19 10.3 Receiver common mode rejection. 19 10.4 Transmitter common mode output voltage 10.5 Input tolerance ... 10.6 Return loss.. .20 10.7 Connector .20 10.8 Connector configuration.. 11 Cabling channel.. ..20 11.1 General conditions.. ..20 11.2 External noise 12 Environmental 12.1 Safety ..20 12.2 Grounding 12.3 Telephone voltages . 12.4 Susceptibility .. .21 12.5 Temperature and humidity .21 12.6 Labelling 21 BIBLIOGRAPHY Figure 1 - Model... .6 Figure 2 - MAC interface . .9 Figure 3 - Interface overview via 100 Q Class F cabling . .10 Figure 4 - MAC interface data stream Figure 5 - State diagram of MLT-3... 13 Figure 6 - Coding scheme of MLT-3.. ..13 Figure 7 - Transmission witn MLT-3. ..14 Figure 8 - Frame format . Figure 9 - Scrambler polynomial and correspondent circuit diagram .16 Figure 10 - Transmission eye diagram . Figure 11 - Transmission eye diagram detail. Figure 12 - Receiver eye diagram. .18 Figure 13 - Receiver common mode rejection test.. .19 Figure 14 - Common mode voltage test . 19 Copyright International Organization for Standardization nse from IHS Not for Resale 14165-114 @ ISO/IEC:2005(E) - 4 Table 1 - DC characteristics 11 Table 2 - AC characteristics Table 3 - Signal mapping. Table 4 - Delay requirements .. ...13 Table5-Controlfunctions. Table 6 - Eye diagram mask at points R1 and R2 Table 7 - Return loss.. .20 Table 8 - Connector configuration.. .20 Copyright International Organization for Standardization Reproduced by IHS unde Not for Resale 14165-114 @ ISO/IEC:2005(E) - 5 INFORMATION TECHNOLOGY - FIBRE CHANNEL - Part 114: 100 MB/s balanced copper physical interface (FC-100-DF-EL-S) FORE