ISO INTERNATIONAL STANDARD 9727-5 First edition 2007-05-15 Cylindrical cork stoppers - Physical tests -- Part 5: Determination of extraction force Bouchons cylindriques en liege-Essaisphysiques- Partie5:Détermination delaforced'extraction Referencenumber ISO 9727-5:2007(E) so ISO2007 ISO 9727-5:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The iso Central Secretariat accepts no liability in this area. Adobe is atrademark of AdobeSystems Incorporated. Details of the sofware products used to create this PDF file can be found in the General Info relative to the fle; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsoO at the address below or IsO's member body in the country of the requester. ISO copyrightoffice Case postale56.CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @Iso2007-All rights reserved ISO 9727-5:2007(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies non-governmental, in liaison with isO, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Iso shall not be held responsible for identifying any or all such patent rights. ISO 9727-5 was prepared by Technical Committee ISO/TC 87, Cork. This first edition of IS 9727-5, together with the other parts of Is0 9727:2007, cancels and replaces IsO9727:1991,whichhasbeentechnicallyrevised. Part 1: Determination of dimensions Part 2: Determination of mass and apparent density for agglomerated cork stoppers Part 3: Determination of humidity content Part 4: Determination of dimensional recovery after compression Part 5:Determination of extraction force Part 6: Determination of liquid tightness Part 7: Determination of dust content IS0 2007 -All rights reserved ili INTERNATIONAL STANDARD ISO 9727-5:2007(E) Cylindrical cork stoppersPhysicaltests- Part 5: Determination of extractionforce 1 Scope This part of Iso 9727 specifies a test method for determining the maximum force necessary to extract a cylindrical cork stopper. It is applicable to all types of cylindrical cork stoppers ready for use, intended to be completely inserted in the bottleneck(straightcorkstoppers) 2Normative references references, only the edition cited applies. For undated references, the latest edition of the referenced document (includinganyamendments)applies. Iso633,Cork-Vocabulary Terms and definitions For the purposes of this document, the terms and definitions given in Iso 633 and the following apply. 3.1 straight cork stopper 《rasdebague stopper which is completely introduced in the bottle neck, its superior end reaching the top border of the bottle 4 Materials 4.1 Acetone, for cleaning the glass tubes or the necks of the empty bottles. 5 Apparatus 5.1 16 mm. 5.2 Glass tubes, with an internal diameter of 18,5 mm ±0,2 mm or an internal diameter of (d± 0,2) mm (where d is the bore diameter of the bottle intended to be u