ISO INTERNATIONAL STANDARD 9185 Second edition 2007-07-01 Protective clothing Assessment of resistance of materials to molten metal splash Vetements de protectionEvaluation de la résistance des materiaux aux projections de meétal fondu Reference number ISO 9185:2007(E) @ ISO 2007 yIHS under Not for Resale ISO 9185:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT @ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's memberbody in the country of the requester. ISO copyright office Case postale 56. CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2007 - All rights reserved I without license from IHS Not for Resale ISO 9185:2007(E) Contents Page Foreword. Introduction 1 Scope 2 Normative references 3 Terms and definitions. 4 Principle..... 5 Apparatus and materials. 6 Conditioning.. 7 Preparation of test specimens . 8 Operator safety 9 Procedure.... 9.1 Setting up the apparatus. 9.2 Preparation of molten metal orcryolite. 9.3 Attachment of test material to pin frame 9.4 Pouring. 9.5 Examination.. 9.6 Determination of mass of metal poured 10 Iterative testing 11 Voidtests. 8 12 Test report, 8 Annex A (normative) Test conditions for certain metals and for cryolite .. Annex B (normative) Method of test for assessment of thermal characteristics of PvC sensor film.... 11 Bibliography 12 Copyright International Organizationfrstandardizalionghtsreserved ii from IHS Not for Resal ISO 9185:2007(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 9185 was prepared by the European Committee for Standardization (CEN) Technical Committee Technical Committee ISO/TC 94, Personal safetyProtective clothing and equipment, Subcommittee SC 13, Protective clothing, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). This second edition cancels and replaces the first edition (isO 9185:1990), which has been technically revised. This second edition includes the following significant technical changes compared to the first edition: a) new PvC sensor film included; b)Cryolite included as test metal, ISO 2007 - All rights reserved nal Organization for Standardizatio ISO9185:2007(E) Introduction IsO 9185:1990 and EN 373