ISO INTERNATIONAL STANDARD 90-3 Second edition 2000-08-01 Light gauge metal containers Definitions and determination of dimensions and capacities Part 3: Aerosol cans Récipients metalliques légers Définitions et détermination des dimensions et des capacités Partie 3:Boitierspouraérosols Reference number ISO 90-3:2000(E) ISO @ ISO 2000 y IHS under lic 975001,User=bao,zhou No r itted without license from IHS ISO 90-3:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this area. Adobe is a trademarkof Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event ?ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland @ ISO 2000 - All rights reserved py IHS unde ermittedwithoutlicense from IHS ISO 90-3:2000(E) Contents Page Foreword .iv Introduction 1 Scope 2 Terms and definitions .. 3 Determination of dimensions .. 4 Determination of capacities.. .9 5 Tolerances on capacities 10 6 Designation .... Annexe A (informative) Dimensions of the top end of three-piece necked-in tinplate cans... Copyrighntemagananforsdardzaed ii d by IHS under license with Not fe ISO 90-3:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this part of isO 90 may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 90-3 was prepared by Technical Committee ISO/TC 52, Light gauge metal containers, Subcommittee SC 6, Aerosol containers. This second edition cancels and replaces the first edition (isO 90-3:1986) which has been technically revised. Iso 9o consists of the following parts, under the general title Light gauge metal containers - Definitions and determination of dimensions and capacities: Part 1:Open-top cans Part 2: General use containers Part 3:Aerosol cans NOTE An "open-top can" is a can one end of which is double-seamed after filling. A "general use container" is a container which is sealed after filling with a closure that need not be double-seamed. Annex A of this International Standard is for information only. lafOrganizationfor Standardizatior @ ISO 2000 - All rights reserved ISO 90-3:2000(E) Introduction Iso 90 consists of three parts which group definitions, methods of determination of dimensions and capacities, as well as tolerances and designations of rigid containers made of metal with a maximum nominal material thickness of0,49 mm. V INTERNATIONALSTANDARD ISO 90-3:2000(E) Light gauge metal co