INTERNATIONAL STANDARD ISO 887:2000 TECHNICALCORRIGENDUM 1 Tso Published 2006-01-15 INTERNATIONALORGANIZATIONFORSTANDARDIZATION MEKIYHAPOIHAOPTAHM3ALIMANO CTAHIAPTV3ALIMM·ORGANISATION INTERNATIONALEDENORMALISATION Plain washers for metric bolts, screws and nuts for general purposes General plan TECHNICALCORRIGENDUM1 Rondelles plates pour vis et écrous metriques pour usages generaux - Plan general RECTIFICATIFTECHNIQUE1 Technical Corrigendum 1 to International Standard ISO 887:2000 was prepared by Technical Committee ISO/TC 2, Fasteners. Page 2, Table 2 Delete dimension h = 1,2 mm from the table. Page 4, Table 3, Nominal size (Thread size, d) = 5 mm, Large series, Product grade A, column h Replace h = 1,2 mm by h = 1 mm in the table. Page 4, Table 3, Nominal size (Thread size, d) = 5 mm, Large series, Product grade C, column h Replace h = 1,2 mm by h = 1 mm in the table. ICS 21.060.30 Ref. No. ISO 887:2000/Cor.1:2006(E) sO 2006 - All rights reserved Printed in Switzerland 148519030332331551 STD.ISO BB?-ENGL 20O0 INTERNATIONAL ISO STANDARD 887 Second edition 2000-06-15 Plain washers for metric bolts, screws and nuts for general purposes -- General plan Rondelles plates pour vis et écrous metriques pour usages generaux - Plan general This material is reproduced from ISO documents under Intemational Organization for Standardization (ISO) Copyright License Number IHS/CC/1996. Not for resale No part of these Iso documents may be reproduced in any form, electronic retrieva! System or otherwise, except written consent ofISO (Case postal 56,1211 Geneva Reference number ISO887:2000(E) ISO @ISO2000 STD.ISO BA7-ENGL20OO 48519030832332.490 ISO 887:2000(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this area Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. @ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or iso's member body inthecountry oftherequester. ISO copyright office Case postale 56· CH-1211 Geneva 20 Tel.+41227490111 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland ii IsO2000-Allrightsreserved 3TSBBY-FNGL2OOO h2E·EEE2ERO EULTGh ISO 887:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through isO technical committees.Eachmemberbodyinterestedinasubjectforwhichatechnical committeehasbeenestablishedhas therighttoberepresentedonthatcommittee.Internationaforganizations,governmentalandnon-governmental,in liaison with so, also take part in the work. iso collaborates closely with the International 'Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 3. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this Inter