BS IS08017:2007 BSl Standards Publication Tools for moulding- Guide pillars, straight and shouldered, and locating guide pillars, shouldered bsi. BS ISO 8017:2007 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 8017:2007. The UK participation in its preparation was entrusted to Technical Committee MTE/12, Tools for pressing and moulding. A list of organizations represented on this committee can be obtained on request to its secretary. This publication does not purport to include all the necessary provisions of a contract. Users are responsible for its correct application. @ The British Standards Institution 2016. PublishedbyBSIStandardsLimited2016 ISBN9780580955334 ICS 25.120.30 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 August 2016. Amendments/corrigenda issued since publication Date Text affected BS ISO 8017:2007 INTERNATIONAL ISO STANDARD 8017 Second edition 2007-02-01 Tools for moulding Guide pillars. straight and shouldered, and locating guide pillars, shouldered Outillage de moulage - Colonnes de guidage, droites et épaulées, etépaulées avecplot de centrage Reference number ISO 8017:2007(E) @ ISO 2007 BS ISO 8017:2007 ISO 8017:2007(E) PDF disclaimer shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, ISO copyright office Case postale 56: CH-1211Geneva20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org ii @ISO 2007-All rights reserved BS ISO 8017:2007 ISO 8017:2007(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeer non-governmental, in liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. InternationalStandardsaredraftedinaccordancewiththerulesgivenintheISO/lECDirectives,Part2 International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent ISO 8017 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This second edition cancels and replaces the first edition (IsO 8017:1985), of which it constitutes a mino revision. In particular, the references given in Clause 2, which are not mentioned in the text, have been listed @ ISO 2007 - All rights reserved ii BS ISO 8017:2007 BS ISO 8017:2007 INTERNATIONAL STANDARD ISO 8017:2007(E) Tools for moulding Guide pillars, straight and shouldered, and locating guide pillars, shouldered 1 Scope This International Standard specifies the dimensions and tolerances, in millimetres, for headed, straight and shouldered guide pillars and shouldered locating guide pillars intended for use in moulds. Dimensions Guide pillars, straight - Type A The dimensions of straight guide pillars of type A shall conform to the indications of Figure 1 and Table 1. Surface roughness values in micrometres 00.1A Ra 0.