ISO INTERNATIONAL STANDARD 7675 Second edition 2003-06-01 Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Chlorinated poly(vinyl chloride) (PVC-C) Systemes de canalisations en plastique pour I'evacuation des eaux- vannes et des eaux usées (a basse et a haute température) a I'interieur des batiments — Poly(chlorure de vinyle) chlore (PVC-C) Reference number ISO 7675:2003(E) ISO @ ISO 2003 y IHS under ted without license from IHS Not for Resale ISO 7675:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2003 - All rights reserved py IHS unde ermittedwithoutlicense from IHS Not for Resale ISO 7675:2003(E) Contents Page Foreword Introduction 1 Scope 2 Normative references 3 Symbols and abbreviations .. 4 Material... 5 General characteristics 6 Geometrical characteristics... 7 Mechanical characteristics of pipes 21 8 Physical characteristics. 9 Performance requirements 10 Sealing rings. 11 Adhesives 12 Marking.. 13 Installation of piping systems . Annex A (informative) Additional characteristics of PvC-C pipes and fittings. Bibliography .... Copyright International Organizaion for Standardization rights reserved ili se from IHS Not for Resale ISO 7675:2003(E) Foreword IsO (thie International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has beer non-governmental,inliaisonwithIsO,also take partin the work.Iso collaboratesclosely with the International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. transport of fluids, Subcommittee Sc 1, Plastics pipes and fittings for soil, waste and drainage (including land drainage). Thissecondeditioncancelsandreplacesthefirstedition(lSO7675:1991),whichhasbeentechnicallyrevised Iso 2003 - All rights reserved ional Organizationfor Standardizatior ISO 7675:2003(E) Introduction Pipes and fittings conforming to this International Standard also meet the requirements of EN 1566-1 which buildings (application area code“B", see EN 1566-1) only. V Not for Resale aadizao No reproductic neworkingmitedwithout licenefrmH Not for Resale INTERNATIONAL STANDARD ISO 7675:2003(E) Plastics piping systems for soil and waste discharge (low and high temperature) inside buildings Chlorinated poly(vinyl chloride) (PVC-C) 1 Scope This International Standard specifies the requirements for chlorinated poly(vinyl chloride) (PvC-C) pipes and fittings f