ISO INTERNATIONAL STANDARD 7132 Third edition 2003-12-01 Earth-moving machinery Dumpers - Terminology and commercial specifications Engins de terrassement - Tombereaux - Terminologie et spécifications commerciales Reference number ISO 7132:2003(E) ISO ISO 2003 Not for Resale ISO 7132:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's memberbody in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyihtinteratinal organization for Standardization @ ISO 2003 - All rights reserved itted without license from IHS Not for Resale ISO 7132:2003(E) Contents Page Foreword iv 1 Scope 2 Normative references 3 Terms and definitions.. 3.1 General. 3.2 Performance 4 Base machine 4.1 Types of dumper ... 2 4.2 Dimensions (see ISO 6746-1). 10 4.3 Masses ....... 14 4.4 Component nomenclature. 14 5 Performancecharacteristics. 21 6 Commercial literature specifications (Sl units). 21 6.1 Engine. 21 6.2 Transmission. 22 6.3 Drive axle(s) 22 6.4 Steering. 22 6.5 Brakes 23 6.6 Tyres. 23 6.7 Hydraulic system 23 6.8 Suspension.... 6.9 Body 24 6.10 Operator station 25 6.11 25 6.12 Systemfluidcapacities 25 6.13 Overall dumper dimensions... 26 Annex A (normative) Dimensions for dumpers.... .27 Annex B (normative) Dimensions for compact dumpers. 28 Copyrght International Organizaion forstandardizationrights reserved ii se from IHS Not for Resa ISO 7132:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through isO technical committees. Each member body interested in a subject for which a technical committee has been non-governmental, in liaison with isO, also take part in the work. isO collaborates closely with the InternationalElectrotechnicalCommission(iEC)onallmattersofelectrotechnicalstandardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 7132 was prepared by Technical Committee ISO/TC 127, Earth-moving machinery, Subcommittee SC 4, Commercial nomenclature, classification and rating. This third edition cancels and replaces the second edition (IsO 7132:1990), which has been technically revised. onal Organization for Standardizatior ISo2003—Allrightsreserved ISO 7132:2003(E) INTERNATIONAL STANDARD Earth-moving machinery Dumpers Terminology and commercial specifications 1 Scope This International Standard establishes a terminology for, and the content of, commercial literature specifications for self-propelled dumpers (including compact du