ISO INTERNATIONAL STANDARD 6967 Third edition 2006-02-01 Aircraft ground equipment Main deck loader Functional requirements Materiel au sol pour aéronefs - Chargeur de pont principal - Exigencesfonctionnelles (na1 1211A 1211 nninn Reference number ISO 6967:2006(E) ISO @ ISO 2006 ISO 6967:2006(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobeis atrademarkofAdobeSystems Incorporated. parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. 1211A 1211 inn inn ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2006 - All rights reserved ISO 6967:2006(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (iSO member bodies). The work of preparing International Standards is normally carried out through IsO non-governmental, in liaison with isO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 6967 was prepared by Technical Committee ISO/TC 20, Aircraft and space vehicles, Subcommittee SC 9 Aircargo and ground equipment. This third edition cancels and replaces the second edition (IsO 6967:1994), which has been technically revised. 1n n101- @ Iso 2006 - All rights reserveo ili ISO 6967:2006(E) Introduction ThisInternationalStandard specifiesthefunctional requirementstobetakenintoaccountbymanufacturers for the design of aircraft main deck cargo container and pallet loaders. Throughout this International Standard, the minimum essential criteria are identified by use of the key word ‘shall'. Recommended criteria are identified by use of the key word 'should' and, while not mandatory, are Deviation from recommended criteria should only occur after careful consideration and thorough service evaluation have shown alternative methods to provide an equivalent level of safety. 1211 inn iv @Iso2006-All rightsreserved ISO 6967:2006(E) INTERNATIONALSTANDARD Aircraft ground equipment Main deck loader Functional requirements 1 Scope This International Standard specifies the functional requirements for a self-propelled loader capable of raising air cargo unit load devices (ULDs) with base dimensions and maximum mass as given in Table 1. Table 1 Base dimensions and maximum mass ISO8097:2001 Length Width Maximum gross mass basesizecode mm (in) mm (in) kg (lb) A 3 175 (125) 2 235 (88) 6 804 (15 000) M 3 175 (125) 2 438 (96) 6 804 (15 000) R 4 978 (196) 2 438 (96) 11 340 (25 000) G 6 058 (238,5) 2 438 (96) 13 600 (30 000) (na1 loaders.Other requirements can be found i