ISO INTERNATIONAL STANDARD 6360-2 Second edition 2004-11-01 Dentistry Number coding system for rotary instruments - Part 2: Shapes Artdentaire- Systeme de codification numérique pour instruments rotatifs Partie 2: Formes de réalisation Reference number ISO 6360-2:2004(E) @ ISO 2004 Not for Resale ISO 6360-2:2004(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2004 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's memberbody in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland CopyightInternatinal organization for Standardization @ ISo 2004 - All rights reserved vithout license from IHS Not for Resale ISO 6360-2:2004(E) Contents Page Foreword iv Introduction 1 Scope 2 Normative references 3 Terms and definitions 4 Code numbers for shapes 4.1 General. 4.2 Genericform 4.3 Wheels.... 4.4 Discs.. 4.5 Diamond instruments 5 Shapes and design . 5.1 General shapes and design .. 3 5.2 22 5.3 Special instruments .. .30 5.4 Mandrels and accessories.. 40 5.5 Root-canal instruments 43 Copyrght InternationalOrganizasandardizloghtsreserved ii from IHS Not for Resale ISO 6360-2:2004(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Iso shall not be held responsible for identifying any or all such patent rights. ISO 6360-2 was prepared by Technical Committee ISO/TC 106, Dentistry, Subcommitee SC 4, Dental instruments. This second edition cancels and replaces the first edition (IsO 6360-2:1986), which has been technically revised. It also incorporates the Amendment ISO 6360-2:1986/Amd.1:1991. IsO 6360 consists of the following parts, under the general title Dentistry - Number coding system for rotary instruments: Part 1: General characteristics Part 2: Shapes Part 3: Specific characteristics of burs and cutters Part 4: Specific characteristics of diamond instruments Part 6: Specific characteristics of abrasive instruments Part 7: Specific characteristics of mandrels and special instruments The following part is under preparation: Part 5: Specific characteristics of root-canal instruments ization for Standardizatior ISO2004-All rightsreserved ISO 6360-2:2004(E) Introduction This part of isO 6360 is one of a series of International Standards relating to dental rotary instruments. A wide varietyof dentalrotaryinstruments,includingroot-canalinstruments,ismanufacturedthroughouttheworldfoi usebythedentalprofession. Iso 6360 provides a general