ISO INTERNATIONAL STANDARD 6022 Second edition 2006-02-01 Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series Transmissions hydrauliques Dimensions d'interchangeabilite des vérins 25 MPa (250 bar) a simple tige Reference number ISO 6022:2006(E) @ ISO 2006 ISO 6022:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In ?ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2006-All rights reserved ISO 6022:2006(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through IsO InternationalElectrotechnicalCommission(lEC)onallmattersofelectrotechnicalstandardization. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 6022 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommittee SC 3 Cylinders. This second edition cancels and replaces the first edition (ISsO 6022:1981 and ISO 8137:1986), which have been technically revised. @ ISO 2006 - All rights reserved ili ISO 6022:2006(E) Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of such systems is the fluid power cylinder. This is a device that converts power into linear cylindrical bore. iv @ISO2006-All rights reserved INTERNATIONAL STANDARD ISO 6022:2006(E) Hydraulic fluid power Mounting dimensions for single rod cylinders, 25 MPa (250 bar) series 1 Scope This International Standard establishes mounting dimensions for hydraulic cylinders for use at 25 MPa [250 bar1], as required for interchangeability of these cylinders. NOTE (25o bar)cylinders anddoes not restricttechnicaldevelopment;however,it doesprovidebasicguidelines. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced ISO 1179-12), Connections for general use and fluid power- Ports and stud ends with ISO 228-1 threads with elastomeric or metal-to-metal sealing Part 1: Threaded ports Iso 4395, Fluid power systems and components- Cylinders - Piston rod thread dimensions and types Iso 55983), Fluid power systems and components Vocabulary Iso 6o99, Fluid power systems and components - Cylinders - ldentification code for mounting dimensions and mounting types Iso 6149-14), Connections for fluid power and general use - Ports and stud ends with /so 261 threads and O-ring sealing - Part 1: Ports with O-ring seal in truncated housing Iso6162-1,Hydraulic fluid power- Flangeconnectorswithsplitorone-pieceflangeclampsandmetricor inchs