ISO INTERNATIONAL STANDARD 6020-1 Third edition 2007-08-15 Hydraulic fluid power Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series - Part 1: Medium series Transmissions hydrauliques - Dimensions d'interchangeabilite des vérins 16 MPa (160 bar) a simple tige - Partie 1: Série moyenne Reference number ISO 6020-1:2007(E) @ ISO 2007 y IHS under lic ted without license from IHS Not for Resale ISO 6020-1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below COPYRIGHTPROTECTEDDOCUMENT @ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2007 - All rights reserved I without license from IHS Not for Resale ISO 6020-1:2007(E) Contents Page Foreword. Introduction 1 Scope 2 Normative references 3 Terms and definitions 4 Dimensions 5 Bore sizes 6 Stroke tolerances.. 2 7 Mounting types. 8 Piston rod characteristics..... 9 Identification statement (reference to this part of ISO 6020) Bibliography.... Copyright International Organizaion for Standardizalon'ghts reserved ii ense from IHS Not for Resale ISO 6020-1:2007(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeer non-governmental, in liaison with isO, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 6020-1 was prepared by Technical Committee ISO/TC 131, Fluid power systems, Subcommitee SC 3, Cylinders. This third edition cancels and replaces the second edition (IsO 6020-1:1998) and ISO 8135:1999, which have been technically revised. Iso 6020 consists of the following parts, under the general title Hydraulic fluid power - Mounting dimensions for single rod cylinders, 16 MPa (160 bar) series: Part 1: Medium series Part 2: Compact series Part 3: Compact series with bores from 250 mm to 500 mm @ ISO 2007 - All rights reserved al Organization for Standardizatior ISO 6020-1:2007(E) Introduction In hydraulic fluid power systems, power is transmitted and controlled through a liquid under pressure within an enclosed circuit. One component of such systems is the fluid power cylinder. This is a device that converts power into linear cylindrical bore. Not for Resale aadizao No reproductic neworkingmite