ISO INTERNATIONAL STANDARD 3098-6 First edition 2000-05-01 Technical product documentation - Lettering - Part 6: Cyrillic alphabet Documentation techniquedeproduits-Ecriture- Partie 6:Alphabet cyrillique Reference number ISO 3098-6:2000(E) ISO @ISO2000 ISO3098-6:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this area. AdobeisatrademarkofAdobeSystems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the C ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the countryofthe requester. ISO copyright office Case postale56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland @ISO2000-All rights reserved ISO 3098-6:2000(E) Foreword ISO (theInternationalOrganizationforStandardization)isaworldwidefederationofnational standardsbodies(iSO memberbodies).TheworkofpreparinglnternationalStandardsisnormallycarriedoutthroughSOtechnica Commission (IEC) on all matters of electrotechnical standardization. International Standards aredrafted inaccordance with the rulesgiven intheISO/lEC Directives, Part 3. Attention is drawn to the possibility that some of the elements of this part of IsO 3098 may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. definitionandrelateddocumentation,SubcommitteeSC1,Basicconventions. This first edition of ISO 3098-6 cancels and replaces the first edition of ISO 3098-4:1984, which has been technically revised. IsO 3098 consists of the following parts, under the general title Technical product documentation-Lettering: PartO:Generalrequirements[becomesPart1withthenextrevision] Part2:Latinalphabet, numeralsandmarks 一 Part3:Greekalphabet -Part4:DiacriticalandparticularmarksfortheLatinalphabet —Part5:CADletteringoftheLatinalphabet, numeralsandmarks Part6:Cyrillicalphabet ISO2000-All rights reserved ili ISO3098-6:2000(E) INTERNATIONALSTANDARD Technical product documentation Lettering Part 6: Cyrillic alphabet Scope drawings and associated documents. It primarily concerns characters written with the aid of stencils, but is equally applicabletofreehandletteringorotherappropriatemethods. 2Normative reference The following normative document contains provisions which, through reference in this text, constitute provisions of this part of isO 3098. For dated references, subsequent amendments to, or revisions of, this publication do not of applying the most recent edition of the normative document indicated below. For undated references, the latest edition of the normativedocument referred to applies.Members of iSO and IEC maintain registers of currently valid InternationalStandards ISO3098-0:1997,Technicalproductdocumentation-Lettering-Part0:Generalrequirements. 3 Generalrequirementsanddimensions Forthegeneral requirementsandthedimensions of characters, numeralsand marks, see IsO3098-0. To obtain constant line density, avoid blotting at intersecting lines and facilitate writing, the characters shall be formed so that lines cross, or meet, at approximate right angles. 4 Samples theCyrillicRussianalphabet. 1) Other Cyrllic alphabets in