ISO INTERNATIONAL STANDARD 2976 Second edition 2005-04-01 Coated abrasives Abrasive belts Selection of width/length combinations Abrasifs appliqués - Bandes abrasives - Sélection des combinaisons largeurs/longueurs Reference number ISO 2976:2005(E) @ISO2005 ISO 2976:2005(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademarkof Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, Iso's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2005 - All riahts reserved ISO 2976:2005(E) Contents Page Foreword.. 1 Scope.. 2 Normative references .... 3 3.1 Dimensions and limit deviations for standardized sizes .. 3.2 Length difference.. 3.3 Test conditions.... 10 4 Designation, 10 5 Marking... 10 Annex A (informative) Dimensions of abrasive belts, selection of width/length combinations ......... 11 A."ahtsreserved ii ISO 2976:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies InternationalElectrotechnicalCommission(iEC)onallmattersofelectrotechnicalstandardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 2976 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 5, Grinding wheels and abrasives. This second edition cancels and replaces the first edition (IsO 2976:1973), which has been technically revised. @ISO2005-Allriahts reserved ISO 2976:2005(E) INTERNATIONAL STANDARD Coated abrasives Abrasive belts Selection of width/length combinations 1 Scope This International Standard specifies the nominal dimensions, and limit deviations of abrasive belts. It also specifies the designation and marking of these abrasive belts. This International Standard is applicable to abrasive belts intended for use on hand-held grinding machines and stationary grinding machines. 2 Normative references Thefollowingreferenceddocumentsareindispensable forthe applicationof this document.For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. Iso 554:1976, Standard atmospheres for conditioning and/or testing— Specifications Requirements 3.1Dimensions and limit deviations for standardized sizes See Figure 1, Table 1 and Table 2. ahts reserved 1 ISO 2976:2005(E) Key abrasive belt of width T and total length L = 2a + dπ 2 roll diameterd D distance between roll axes Figure 1 ISO2005-All riahts reserved ISO2976:2005(E) Table 1 Pre