ISO INTERNATIONAL STANDARD 2342 Secondedition 2003-12-01 Slotted headless screws with shank Vissanstetefendues,afut Reference number ISO 2342:2003(E) ISO X @ ISO 2003 ISO 2342:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. .In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the @ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either Iso at the address below or ISo's member body in the country of the requester. ISO copyright office Case postale 56·CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland := @ISO 2003-All rights reserved ISO 2342:2003(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeer non-governmental, in liaison with IsO, also take part in the work. ISO collaborates closely with the International International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. isO shall not be held responsible for identifying any or all such patent rights. ISO 2342 was prepared by Technical Committee ISO/TC 2, Fasteners. This second edition cancels and replaces the first edition (iSO 2342:1972), which has been technically revised @ ISO 2003 - All rights reserved ii INTERNATIONALSTANDARD ISO 2342:2003(E) Slotted headless screws with shank 1Scope This International Standard specifies the characteristics of slotted headless screws with shank with threads from M1 up to and including M10. If, in special cases, specifications other than those listed in this International Standard are required, they should be selected from existing International Standards, e.g. ISO 261, ISO 898-5, ISO 965-2, ISO 3506-3, ISO 8839 and ISO 4759-1. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated (including any amendments) applies. IsO225,FastenersBolts,screws,studsandnuts-Symbolsanddesignationsofdimensions similar threaded fasteners not under tensile stresses IsO965-2,SO general purpose metric screw threads- Tolerances-Part2:Limits of sizes forgeneral purpose external and internal screwthreadsMedium quality IsO 3269, Fasteners —Acceptance inspection IsO 3506-3, Mechanical properties of corrosion-resistant stainless-steel fasteners - Part 3: Set screws and similarfasteners not under tensile stress IsO 4042, Fasteners -Electroplated coatings ISO 4753, Fasteners-Ends of parts with external ISO metric thread IsO 4759-1, Tolerances for fasteners - Part 1: Bolts, screws, studs and nuts - Product grades A, B and C Iso 6157-1, Fasteners Surface discontinuities — Part 1: Bolts, screws and studs for general requirements IsO 8839, Mechanical properties of fasteners -Bolts, screws, studs and nuts made of non-ferrous metals ISO10683,Fasteners—Non-electrolyticallyappliedzincflakecoatings ISO 2003 - All rights reserved ISO 2342:2003(E) 3Dimensions See Figure 1 and Table 1. Symbols and designations of dimensions are specifie