ISO INTERNATIONAL STANDARD 22034-1 First edition 2007-10-01 Steel wire and wire products Part 1: General test methods Fil et produits de fil en acier- Partie 1: Methodes d'essai generales Reference number ISO 22034-1:2007(E) @ ISO 2007 yIHS under itted without license from IHS Not for Resale ISO 22034-1:2007(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT @ISO2007 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's memberbody in the country of the requester. ISO copyright office Case postale 56. CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISo 2007 - All rights reserved I without license from IHS Not for Resale ISO 22034-1:2007(E) Contents Page Foreword 1 Scope 2 Normative references 3 Tensile test.. 4 Simple torsion test.. 5 Reverse bend test. 6 Wrapping test 7 Bend test.. 8 Reverse torsion test 9 Compression test. 10 Deep etch test .. 11 Hardness test . 12 Quench hardenability test.... 13 Fatigue test (bend and axial) . 14 Coil set measurements. 15 Artificial ageing .... 16 Decarburization test, 17 Non-destructive tests .. 18 Grain size test 19 Segregation test.. 20 Nonmetallic inclusion test.... 21 Chemical analysis. 22 Retests ii from IHS Not for Resale ISO 22034-1:2007(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the IsO/lEc Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 22034-1 was prepared by Technical Committee ISO/TC 17, Steel, Subcommittee SC 17, Steel wire rod and wire products. IsO 22034 consists of the following parts, under the general title Steel wire and wire products: Part 1: General test methods Part 2: Tolerances on wire dimensions ISO 2007 - All rights reserved nal Organization for Standardizatior INTERNATIONAL STANDARD ISO22034-1:2007(E) Steel wire and wire products - Part 1: General test methods 1 Scope This part of IsO 22034 specifies the methods for the general testing of steel wire and wire products which section (either round or special section). It includes tensile testing, torsion testing, reverse bend testing, a quench hardenability test, a fatigue test, wire cast measurement, artificial ageing, a decarburization test, non-destructive tests, a grain size test, a