INTERNATIONAL STANDARD ISO 19472:2006 TECHNICAL CORRIGENDUM 1 Published 2006-11-01 INTERNATIONALORGANIZATION FOR STANDARDIZATION MEKIYHAPOAHA OPTAHV3ALMNO CTAHIAPTW3ALIMИ ORGANISATION INTERNATIONALE DE NORMALISATION Machinery for forestry Winches Dimensions, performance and safety TECHNICAL CORRIGENDUM 1 Materielforestier- Treuils一 Dimensions, performance et sécurite RECTIFICATIFTECHNIQUE1 Technical Corrigendum 1 to International Standard ISO 19472:2006 was prepared by Technical Committee ISO/TC 23, Tractors and machinery for agriculture and forestry, Subcommittee SC 15, Machinery for forestry. Page 4, 5.1.2 Replace Equation (3) by the following: 元 K (3) (1,04d)2 ICS 65.060.80 Ref. No.ISO 19472:2006/Cor.1:2006(E) @ IS0 2006 - All rights reserved raanizationfor Standardizationrland ISO INTERNATIONAL STANDARD 19472 First edition 2006-03-15 Machinery for forestry Winches Dimensions, performance and safety Materiel forestier Treuils -Dimensions, performance et sécurité Reference number ISO 19472:2006(E) @ ISO 2006 ISO 19472:2006(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In ?ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2006 - All rights reserved ISO 19472:2006(E) Contents Page Foreword. iv 1 Scope 2 Normative references 3 Terms and definitions.. 4 Symbols 5 Performance requirements 5.1 Drum storage capacity .... 5.2 Line pull, F. 5.3 Line speed, v. 6 Safety requirements 6.1 Mechanical safety ... 6.2 Drum.. 6.3 Rope breaking load 6.4 Rope fastening ... 6.5 Brake... 6.6 Controls 6.7 Overload device 6.8 6.9 Moving parts for power transmission of winches. L Information for use .. 7.1 Instructionhandbook 7.2 Marking ....... 7.3 Warnings..... Bibliography. n'ghts reserved ili ISO19472:2006(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through sO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with iso, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. Iso shall not be held responsible for ide