ISO INTERNATIONAL STANDARD 17705 First edition 2003-11-01 Footwear Test methods for uppers, lining and insocks Thermal insulation Chaussures Méthodes d'essai des tiges, de la doublure et des premieres de proprete Isolation thermique Reference number ISO 17705:2003(E) ISO @ ISO 2003 ISO 17705:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2003 - All rights reserved ISO 17705:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been non-governmental, in liaison with isO, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 17705 was prepared by CEN (as EN 13521:2001) and was adopted, under a special "fast-track procedure", by Technical Committee ISO/TC 216, Footwear, in parallel with its approval by the ISO member bodies For the purposes of international standardization, a list of corresponding International and European Standards for which equivalents are not given in EN 13521 has been added as Annex ZZ ization'ghts reserved ii ISO 17705:2003(E) EN 13521:2001 (E) Contents page Foreword. .3 Scope 4 2 Normative references . 3 Terms and definitions. .4 4 Apparatus and material .... 5 Sampling and conditioning.. 6 Test method.. 6 6.1 Principle.. 6.2 Procedure 7 Expression of results 8 Test report @ ISO 2003 - All rights reserved ISO 17705:2003(E) EN13521:2001 (E) Foreword This European Standard has been prepared by Technical Committee CEN/TC 309 "Footwear", the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2oo2, and conflicting national standards shall be withdrawn at the latest by May 2002. Switzerland and the United Kingdom. Oraanizationforstandardizalion'ghtsreserved Copvriaht International Oraanization for Standardizatior ISO 17705:2003(E) EN 13521:2001 (E) 1 Scope insocks irrespective of the material, in order to assess the suitability for the end use. 2 Normative references This European Standard incorporates by dated or undated reference, provisions from other publications. These normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For dated references,su