ISO INTERNATIONAL STANDARD 17703 First edition 2003-11-01 Footwear Test methods for uppers High temperature behaviour Chaussures Méthodes d'essai des tiges - Comportement aux températuresélevees Reference number ISO 17703:2003(E) ISO @ISO2003 T by IHS under lic itted without license from IHS ISO 17703:2003(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ISO2003-All rights reserved icensee=Aramco HQ/998075510 itted without license from IHS ISO 17703:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted bythetechnical committeesarecirculatedto thememberbodiesforvoting.Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. procedure", by Technical Committee ISO/TC 216, Footwear, in parallel with its approval by the ISO member bodies. Standards for which equivalents are not given in EN 13519 has been added as Annex ZZ. ii ISO 17703:2003(E) EN13519:2001 (E) Contents page Foreword. 1 Scope 2 Normative references .4 3 Terms and definitions. .4 4 Apparatus and material... 5 Sampling and conditioning. 6 Test method.. 6.1 Principle ... 6.2 Procedure 7 Expression of results 8 Test report Bibliography 2 CopyrightInternational Organization for Standardization Iso 2003-All rights reserved THS under nse from IHS :31 MDT ISO 17703:2003(E) EN 13519:2001 (E) Foreword This European Standard has been prepared by Technical Committee CEN/TC 309 "Footwear", the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by May 2002, and conflicting national standards shall be withdrawn at the latest by May2002. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following Switzerland and the United Kingdom. 3 edwithoutlicense from IHS 1MD aadizao neworkingmitedwithout licenefrmH ISO 17703:2003(E) EN 13519:2001 (E) 1 Scope This European Standard specifies a test method for determining the effect of heat on the tensile strength of uppers 2 Normative references normative references are cited at the appropriate places in the text, and the publications are listed hereafter. For Standard only when incorporated in it by amendment or revision. For undated references the latest edition of the publication referred to applies (including amendments). EN12222 Footwear - Standard atmospheres for condit