ISO INTERNATIONAL STANDARD 17652-2 First edition 2003-05-15 Welding Test for shop primers in relation to welding and allied processes - Part 2: Welding properties of shop primers Soudage Essai sur peintures primaires en relation avec le soudage etlestechniquesconnexes- Partie 2: Proprietés relatives au soudage des peintures primaires Reference number ISO 17652-2:2003(E) ISO @ISO2003 y IHS under ted without license from IHS Not for Resale ISO17652-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademarkof Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ISO 2003 -All rights reserved ermittedwithoutlicense from IHS Not for Resale ISO 17652-2:2003(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen non-governmental, in liaison with IsO, also take part in the work. Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 17652-2 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 44, Welding and allied processes, Subcommittee SC 10, Unification of requirements in the field of metal welding, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Standard...". Iso 17652 consists of the following parts, under the general title Welding — Test for shop primers in relation to welding and allied processes: Part1:Generalrequirements Part 2: Welding properties of shop primers Part 3: Thermal cutting Part 4: Emission of fumes and gases ii Not for Resale ISO 17652-2:2003(E) Contents page Foreword. .v 1 Scope 2 Normative references 3 Terms and definitions... 2 4 Rating test. 4.1 Principle.. 4.2 Preparation of test piece ... 4.3 Procedure... 4.3.1 4.3.2 Breaking of the test weld 4 4.4 Examination and determination of porosity. 4.5 Test report 5 Weldability test 5.1 5.2 Preparation of test piece 5.3 Procedure 5.3.1 General 5.3.2 Tack welding 5.3.3 Welding.. 5.4 Weld evaluation. 5.4.1 Visual examination. 5.4.2 Internal examination .... 5.5 Test report ... AnnexA(informative)Exampleofatestreportforratingtestofweldpropertiesofshopprimers... Annex ZA (informative) Corresponding International and European Standards for which equivalents are not given in the text... CopyrightInternational Organizatio