ISO INTERNATIONAL STANDARD 17642-3 First edition 2005-03-15 Destructive tests on welds in metallic materials Cold cracking tests for weldments Arc welding processes - Part 3: Externally loaded tests Essais destructifs des soudures sur matériaux métalliques Essais de fissuration a froid des assemblages soudés Procédés de soudage a I'arc- Partie 3: Essais sur éprouvette soumise a une charge exterieure Reference number ISO 17642-3:2005(E) @ISO 2005 PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In ?ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 : CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ISO 2005-All rights reserved ISO 17642-3:2005(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen non-governmental, in liaison with IsO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. isO shall not be held responsible for identifying any or all such patent rights. Technical Committee IsO/TC 44, Welding and allied processes, Subcommittee SC 5, Testing and inspection of welds, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Standard...". IsO 17642 consists of the following parts, under the general title Destructive tests on welds in metallic materials - Cold cracking tests for weldments Arc welding processes: Part 1: General Part 2: Self-restraint tests Part3:Externally loadedtests given in the text. ISO 2005 - All rights reserved ili Contents page Foreword. 1 Scope 2 Normative references .. 3 Terms and definitions 4 Designation and symbols .... 5 Principle 6 Description of the tests .2 6.1 General... 6.2 Implant-test. 7 Test report. ..10 Annex A (informative) Test report for implant test .. Annex ZA (normative) List of corresponding European and International Standards for which equivalents are not given in the text.... ..12 iv ISO2005-All rights reserved ISO17642-3:2005(E) Foreword the secretariat of which is held by DIN, in collaboration with Technical Committee ISO/TC 44 "Welding and allied processes". This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement,at thelatest by September 2oo5,and conflictingnational standards shall be withdrawnatthelatestbySeptember2005. materials - Cold cracking tests for weldments - Arc welding processes: - Part 1: General - Part