ISO INTERNATIONAL STANDARD 14923 First edition 2003-07-01 Thermal spraying Characterization and testing of thermally sprayed coatings Projectionthermique— Caracterisationetessaisdesrevetements obtenusparprojectionthermique Reference number ISO 14923:2003(E) ISO @ISO2003 by IHS under lic Not for Resale ISO14923:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ationalgazaiSandardizato @ISO2003-All rights reserved ermittedwithoutlicense from IHS Not for Resale ISO14923:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 14923 prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee IsO/Tc 107, Metallic and other inorganic coatings, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Standard..." ii ISO 14923:2003(E) Contents Page Foreword. .v 1 Scope 2 Normative references. 3 Terms and definitions. 3 4 Manufacturing the coating . 4.1 General.... 4.2 Coating materials.... 4.3 Coating properties... 4.4 Technological and physical properties.. 5 Tests.. 5.1 General. 5.2 Non-destructive test methods .... 5.3 Destructive test methods. Copyright International Organization for Standardization Iso 2003-All rights reserved Not for Resale ISO 14923:2003(E) Foreword and thermally sprayed coatings", the secretariat of which is held by DiN, in collaboration with Technical Committee ISO/TC 107 "Metallic and other inorganic coatings". This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by January 2004, and conflicting national standards shall be withdrawn at the latest by January 2004. countries are bound to implement this European Standard: Austria, Belgium, Czech Republic, Denmark, Finland, Slovakia,Spain,Sweden,SwitzerlandandtheUnitedKingdom. nsefromIHS aadizao No reproductic neworkingmitedwithout licenefrmH Not for Resale ISO 14923:2003(E) Scope This European Standard gives guidance on tests used for characterizations of coatings produced by thermal spraying. It is not possible in this document to go into details regarding the different types of coatings and large numbers of thermal spraying processes exist. The tests listed are procedures and t