ISO INTERNATIONAL STANDARD 14693 First edition 2003-12-15 Petroleum and natural gas industries Drilling and well-servicing equipment Industries du peétrole et du gaz naturel- Equipement de forage et d'entretien des puits Reference number ISO 14693:2003(E) TSO @ ISO 2003 ISO 14693:2003(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ISO2003-All rights reserved ISO 14693:2003(E) Contents Page Foreword.... Introduction 1 Scope.... 2 Normative references 3 Terms, definitions and abbreviated terms......... 3.1 Terms and definitions.. 3.2 Abbreviated terms. 4 Design. 4.1 Design conditions.. 4.2 4.3 Size class designation. 4.4 Rating... 4.5 Load rating basis 4.6 Design safety factor 4.7 Shear strength. 4.8 Specific equipment 4.9 Design documentation 5 Design verification 5.1 General.. 5.2 Design verification function test 5.3 Design verification pressure test 9 5.4 Design verification load test... 10 5.5 Determination of rated load .. 11 5.6 Alternative design verification test procedure and rating 11 5.7 Design verification load-testing apparatus ...... 12 5.8 Design changes... 12 5.9 Records. 12 6 Materials requirements. 12 6.1 General. 12 6.2 12 6.3 Mechanical properties 12 6.4 Material qualification .... 13 6.5 13 6.6 14 7 Welding requirements 7.1 General 16 7.2 Welding qualification .... 16 7.3 Written documentation..... 16 7.4 Control of consumables. 17 7.5 Weld properties .... 17 7.6 Post-weld heat treatment 7.7 Quality control requirements.... 7.8 Specific requirements Fabrication welds 17 7.9 Specific requirements - Repair welds... 8 Quality control.... 18 8.1 18 8.2 Quality control personnel qualifications .. .18 8.3 Measuring and test equipment... 18 ation'ghts reserved ii ISO 14693:2003(E) 8.4 Quality control for specific equipment and components. .19 8.5 Dimensional verification.... .23 8.6 Proof load testing .. .23 8.7 Hydrostatic testing .... 24 8.8 Functional testing.... .24 9 Equipment .24 9.1 General .... .24 9.2 Rotary tables.. .25 9.3 Rotary bushings ... .26 9.4 Rotaryslips.. .27 9.5 Spidersnotcapableofuseaselevators.. .27 9.6 Safety clamps not used as a hoisting device ... 9.7 Manual tongs ....... 33 9.8 Power tongs.... 9.9 Drawworks components. 35 9.10 ,36 Rotary hose... 9.11 Piston mud-pump components ..37 9.12 Antifrictionbearings. ..62 10 Marking... 10.1 Product marking. ..62 10.2 Marking method. .62 11 Documentation. 63 11.1 Record retention..... 11.2 Documentation to be kept by the manufacturer .. ..63 11.3 Documentation to be delivered with the equipment... .63 Annex A (normative) Supplementary requirements.. .65 A.1 Introduction...... .65 A.2 SR1 .Proofloadtesting....... A.3 SR2 Low-temperature testing..... ..65 A.4 SR2A Additional low-temperature testing.... .65 A.5 A.6 SR4 Additional volumetric examination of castings.. A.7 SR5Volumetric examinationofwroughtmaterial.. .66 Annex B (informative) Guidance for qualification of heat-tre