ISO INTERNATIONAL STANDARD 14678 First edition 2005-08-15 Adhesives Determination of resistance to flow (sagging) Adhésifs — Determination de la résistance au fluage (coulure) Reference number ISO 14678:2005(E) @ ISO 2005 Copyright International Organization for Standardization itted without license from IHS Not for Resale ISO14678:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ?ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyightinteratinal organization for Standardization @ ISO 2005 - All rights reserved mittedwithoutlicense from IHS Not for Resale ISO 14678:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 14678 was prepared by the European Committee for Standardization (CEN) in collaboration with Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products, in accordance with the Agreement on technical cooperation between ISO and CEN (Vienna Agreement). Standard..." ii ISO 14678:2005(E) Contents Page Foreword. Introduction..... 1 Scope. 2 Normative references.. 3 Terms and definitions . 4 5 Sampling.. 6 Safety.. 7 Method 1: Use of an applicator to apply a wet film .. 8 Method 2: Use of a plug former. 9 Method 3: Use of a scraper. ...11 10 Method 4: Use of test blocks .. ..13 11 Method 5: Flow from a lap joint.. ...17 12 Method 6: Flow of adhesive through a hole... ..20 13 Method7:Flowofstructuraladhesivefilms. ..21 Copyright International Organization for Standardization @ ISO 2005 - All rights reserved nse from IHS Not for Resale ISO 14678:2005(E) Foreword This European Standard (EN ISO 14678:2005) has been prepared by Technical Committee CEN/TC 193 "Adhesives", the secretariat of which is held by AENOR, in collaboration with Technical Committee ISO/TC 61 "Plastics, Subcommittee Sc 11, Products". This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by February 2006, and conflicting national standards shall be withdrawn at the latest by February 2006. countries are bound to implement this European Standard: Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lith