BS IS0 14649-121:2005 BSl Standards Publication Industrial automation systems and integration - Physical device control - Data model for computerized numerical controllers Part 121: Tools for turning machines bsi. BS IS0 14649-121:2005 BRITISH STANDARD National foreword This British Standard is the UK implementation of IS0 14649-121:2005 The UK participation in its preparation was entrusted to Technical Committee AMT/4, Industrial data and manufacturing interfaces. A list of organizations represented on this committee can be obtained on request to its committee manager. Contractual and legal considerations This publication has been prepared in good faith, however no representation, warranty, assurance or undertaking (express or implied) is or will be made, and no responsibility or liability is or will be reasonableness of this publication. All and any such responsibility and liability is expressly disclaimed to the full extent permitted by the law. This publication is provided as is, and is to be used at the recipient's own risk. The recipient is advised to consider seeking professional guidance with respect to its use of this publication. This publication is not intended to constitute a contract. Users are responsible for its correct application. @ The British Standards Institution 2023 Published by BSI Standards Limited 2023 ISBN 9780 53922216 6 ICS 25.040.20 Compliance with a British Standard cannot confer immunity from legal obligations. This British Standard was published under the authority of the Standards Policy and Strategy Committee on 31 March 2023 Amendments/corrigenda issued since publication Date Textaffected BS IS0 14649-121:2005 INTERNATIONAL ISO STANDARD 14649-121 First edition 2005-09-01 Industrial automation systems and integration — Physical device control Data model for computerized numerical controllers - Part 121: Tools for turning machines Systemes d'automatisation industrielle et integration - -Commande des dispositifs physiques Modele de données pour les controleurs numériques informatisés - Partie 121: Outils pour le tournage Reference number IS0 14649-121:2005(E) ISO @ IS0 2005 BS IS0 14649-121:2005 IS0 14649-121:2005(E) COPYRIGHT PROTECTED DOCUMENT IS0 2005, Published in Switzerland All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior writtenpermission.Permission canberequestedfromeitherIsO attheaddressbeloworIso'smemberbodyinthecountryof the requester. ISO copyright office Ch. de Blandonnet 8 . CP 401 CH-1214 Vernier, Geneva, Switzerland Tel. +41 22 749 01 11 Fax +41 22 749 09 47 [email protected] www.iso.org ii @ IS0 2005 - All rights reserved BSIS014649-121:2005 IS0 14649-121:2005 Contents Page Foreword .iv Introduction. .V 1 Scope .1 2 Normative references 3 Terms and definitions 2. 3.1 Cutting reference point 2 3.2 Tool reference point.. 3.2.1 Prismatic tool item position 3 3.2.2 Round tool item position 4 Tools for turning machines. 3 4.1 Header and references 3 4.2 Turning machine cutting tool 4 4.2.1 Cutting edge properties. 5 4.2.2 Hand of tool type. .8 4.3 Catalogue of turning tool. 4.3.1 8 General turning tool. .8 4.3.2 Turning threading tool 4.3.3 Grooving tool .10 4.3.4 Knurling tool .11 4.3.5 User defined turning tool .12 Annex A (normative) EXPRESS expanded listing .13 Annex B (informative) EXPRESS-G diagram .15 @ IS0 2005 - All rights reserved ii BS IS0 14649-121:2005 IS0 14649-121:2005 Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (IsO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International