ISO INTERNATIONAL STANDARD 14624-6 Flrst edition 2006-04-15 Space systems Safety and compatibility of materials - Part 6: Determination of reactivity of processing materials with aerospace fluids SystemesspatiauxSécuriteetcompatibilitedesmateriaux Partie 6: Détermination de la reactivite des materiaux de traitement avec les fluides aérospatiaux Reference number ISO 14624-6:2006(E) @ISO2006 gugtxgf+"Ygf"Hgd*36*27<37<7:WVE*4246 nnn'ravinti1nff ISO 14624-6:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The Iso Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below @ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, Iso's member body in the country of the requester ISO copyright office Case postale 56: CH-1211 Geneva 20 Tel.+ 4122 749 0111 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii Iso2006-All rights reserved E"eqr[tkijvgf"d["WPG.'E1"1gpqxc."8I"4:226"Ocftkf.'Urckp*cm'tkijvu'tgugtxgf+*"Ygf"Hgd’36*27<37<7:"WVE"4246 knnitrawintiInfi ISO14624-6:2006(E) Contents Page Foreword. iv Introduction. 1 Scope 2 Normative references 3 Termsanddefinitions 4 Safety precautions.. 4.1 Laboratory facilities.... 4.2 Protective clothing... 5 Test procedure .. 5.1 Inspection of sample on receipt. 5.2 Preparation of sample ... 5.3 Test methods...... Annex A (informative) Examples of forms. 10 Bibliography .... ii ruvinti1nft ISO 14624-6:2006(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (Iso member bodies). The work of preparing International Standards is normally carried out through IsO technical committees.Eachmemberbodyinterestedinasubjectfor whichatechnical committee has beer International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 14624-6 was prepared by Technical Committee IsO/TC 20, Aircraft and space vehicles, Subcommittee Sc 14, Space systems and operations. Iso 14624 consists of the following parts, under the general title Space systems - Safety and compatibility of materials: Part 1: Determination of upward flammability of materials - Part 2: Determination of flammability of electrical-wire insulation and accessory materials Part 3: Determination of offgassed products from materials and assembled articles enriched environments -Part 5: Determination of reactivity of system/component materials with aerospace propellants Part 6: Determination of reactivity of processing materials with aerospace fluids Part 7: Determination of permeability and penetration of materials to aerospace fluids IV @ ISO 2006 - All rights reserved ISO 14624-6:2006(E) Introduction The purpose of this part of isO 14624 is to identify changes resulting from exposure of a material to an aerospace fluid that renders either the material unsuitable for use or produc