ISO INTERNATIONAL STANDARD 14368-2 First edition 2003-02-01 Mineral and sapphire watch-glasses - Part 2: Assembly to the case by adhesive or using a gasket Verres de montres mineraux et en saphir- Partie 2: Fixation a la boite par collage ou a I'aide d'un joint Reference number ISO 14368-2:2003(E) ISO @ISO2003 py IHS under lic ted without license from IHS Not for Resale ISO 14368-2:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademarkof AdobeSystems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ationalgazaiSandardizato @Iso2003-All rightsreserved ermittedwithout license from IHS Not for Resale ISO 14368-2:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies non-governmental, in liaison with isO, also take part in the work. isO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEc Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 14368-2 was prepared by Technical Committee ISO/TC 114, Horology, Subcommittee SC 13, Watch- glasses. IsO 14368 consists of the following parts, under the general title Mineral and sapphire watch-glasses: Part 1: Dimensions and tolerances Part 2: Assembly to the case by adhesive or using a gasket Part 3: Qualitative criteria and test methods ii aadizao No reproductic neworkingmitedwithout licenefrmH Not for Resale INTERNATIONAL STANDARD ISO 14368-2:2003(E) Mineral and sapphire watch-glasses Part 2: Assembly to the case by adhesive or using a gasket 1 Scope This part of Iso 14368 specifies dimensional requirements of the interface for the assembly to the case by adhesive or using a gasket for round-shaped mineral and sapphire watch-glasses. Normative references The following referenced documents are indispensable for the application of this document. For dated document (including any amendments) applies. IsO 286-1, /sO system of limits and fits Part 1: Bases of tolerances, deviations and fits IsO 286-2, IsO system of limits and fits - Part 2: Tables of standard tolerance grades and limit deviations for holesandshafts IsO 14368-1, Mineral and sapphire watch-glasses — Part 1: Dimensions and tolerances 3 Terms, definitions and symbols 3.1Terms and definitions For the purposes of this document, the terms and definitions given in ISO 286-1 and ISO 286-2 apply 3.2Symbols The symbols and terms used in Figures 1, 2 and 3 are given in Table 1. Not for Resale ISO 14368-2:2003(E) Table 1 Symbols and terms Symbol Term c gaske