ISO INTERNATIONAL STANDARD 14324 First edition 2003-07-01 Resistance spot welding Destructive tests of welds Method for the fatigue testing of spot welded joints Soudage par résistance Essais destructifs des soudures Méthode pourlesessaisdefatiguesurassemblagessoudesparpoints Reference number ISO ISO 14324:2003(E) @ ISO 2003 y IHS under itted without license from IHS Not for Resale ISO14324:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ationalgazaiSandardizato @Iso2003-All rightsreserved ermittedwithoutlicense from IHS Not for Resale ISO 14324:2003(E) Contents Page Foreword 1 Scope 2 Normative references 3 Termsanddefinitions. 4 Test specimens .. 4.1 Shape and dimensions. 4.2 Test sheets ....... 4.3 Fabrication of test specimen . 5 Testing machine 6 Test methods.. 6.1 Test jig... 6.2 Clamping of test specimens 6.3 Test procedure .... 8 6.4 Termination of test.. 6.5 Determination of L-N data... 7 Analysis and presentation of test results. 10 8 Test report. Copyrght International Organizaion forstandardizationrights reserved ili Not for Resale ISO14324:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isOimember bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has beer non-governmental,inliaisonwithIsO,also take part in the work.Iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. which has been approved by the IsO Council as an international standardizing body in the field of welding @ ISO 2003 - All rights reserved Copyright I ional Organization for Standardizatior Not for Resale INTERNATIONALSTANDARD ISO 14324:2003(E) Resistance spot welding Destructive tests of welds Method for the fatigue testing of spot welded joints Scope steel of sheet thicknesses of 0,5 mm to 6 mm. The test results are not, in general, directly applicable to the fatigue behaviour of a spot-welded component or structure. This procedure can be used for other materials provided proper test conditions (e.g., heating) have been determined. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated document (including any amendments) applies.