ISO INTERNATIONAL STANDARD 13894-2 First edition 2005-07-15 High-pressure decorative laminates - Composite elements - Part 2: Specifications for composite elements with wood-based substrates for interior use Stratifiés décoratifs haute pression Elements composites - Partie 2: Spécifications des éléments composites avec substrats a base de bois pour I'usage intérieur Reference number ISO 13894-2:2005(E) Copyright International Organization for Standardization @ISO2005 ted without license from IHS Not for Resale ISO13894-2:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ?ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland yemainagazainandardizato @ISO2005-All rights reserved nitted without licensefromIHS Not for Resale ISO 13894-2:2005(E) Contents Page Foreword iv 1 Scope 2 Normative references 3 Terms and definitions.. 4 Requirements 5 Properties. 5.1 Appearance 5.2 Dimensional tolerances 5.3 Surface bond strength..... 5.4 Perpendicular tensile strength... 5.5 Glueline quality .... 5.6 Substrate protection against water vapour (thickness swell) 5.7 Surface impact resistance ..... Annex A (informative) Optional properties . A.1 General.. A.2 Resistance to axial withdrawal of wood screws (screw-holding) A.3 Resistance to elevated temperature (short-term exposure) A.4 Resistance to elevated temperature (long-term exposure).... A.5 Resistance to water vapour.... A.6 Flexural strength/flexural modulus of elasticity .... 8 A.7 Continuous-load capability.... A.8 Water resistance (edge swell) Annex B (informative) Reaction to fire. .10 Annex C (informative) Formaldehyde emission.. 11 Copyright Intematinal organizainrsadardizallonghts reserved ii d without license from IHS Not for Resale ISO 13894-2:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through IsO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental,inliaisonwithIsO,also take part in the work.Iso collaborates closely withthe International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. ISO 13894-2 was prepared by Technical Committee ISO/TC 61, Plastics, Subcommittee SC 11, Products Iso 13894 consists of the following parts, under the general title High-pressure decorative laminates Co