ISO INTERNATIONAL STANDARD 11901-1 Second edition 2003-12-01 Tools for pressing Gas springs - Part 1: General specifications Outillage de presse - Ressorts a gaz - Partie1:Specificationsgénérales Reference number ISO 11901-1:2003(E) @ ISO 2003 IHSunder Not for Resale ISO 11901-1:2003(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2003 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either isO at the address below or IsO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211 Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyihtinteratinal organization for Standardization @ ISO 2003 - All rights reserved Not for Resale ISO 11901-1:2003(E) Contents Page Foreword .iv Introduction 1 Scope 2 Normative references . 3 Description and terminology 4 Interchangeability dimensions and characteristics 4.1 General nominal specifications.. 4.2 Gas springs of type 900 and 2 000. 4.3 Gas springs of type 1 500 and 2 500 4.4 Gas springs of type 5 000 to 7 500 .. 4.5 Gas springs of type 15 000 to 100 000 ... 5 Marking.. 6 Technical delivery conditions. 9 7 Designation.. 10 Bibliography Copyrght International Organizainfostandardizationightsreserved ii from IHS Not for Resale ISO 11901-1:2003(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with isO, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. pressing and moulding. This second edition cancels and replaces the first edition (IsO 11901-1:1995), Clauses 4 and 5 of which have beentechnicallyrevised. ISO 11901 consists of the following parts, under the general title Tools for pressing Gas springs: Part1:General specifications Part2:Specificationofaccessories @ ISO 2003 - All rights reserved nal Organization for Standardizatior ISO 11901-1:2003(E) Introduction The attention of the user of iso 11901 is drawn to the fact that gas springs will have to conform to the national regulations of the user country. V HS unde Not for Resale eworkingmitedwihoutlicenefrmH Not for Resale INTERNATIONALSTANDARD