ISO INTERNATIONAL STANDARD 11111-2 First edition 2005-02-15 Textile machinery Safety requirements - Part 2: Spinning preparatory and spinning machines Matériel pour Il'industrie textileExigences de sécurite Partie 2: Machines de preparation de filature et machines de filature Reference number ISO 11111-2:2005(E) @ ISO 2005 ut license from IHS Not for Resale ISO 11111-2:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's memberbody in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 4122 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland CopyightInternatinal organization for Standardization @ ISo 2005 - All rights reserved vithout license from IHS Not for Resale ISO 11111-2:2005(E) Contents Page Foreword. iv Introduction 1 Scope. 2 Normative references . 3 Terms and definitions. 4 List of significant hazards.... 5 Significant hazards and corresponding safety requirements and/or measures. 5.1 General... 5.2 Opening, cleaning, blending machines ... 5.2.1 5.2.2 Automated blending bale openers, 5.2.3 Teasers, willows.... 5.2.4 Bale breakers and hopper feeders . 6 5.2.5 Moving bin emptiers .. 5.2.6 Bunker emptiers. 5.3 Wool scouring (wool washing) machines ..... 5.4 Baling machines........ 5.5 Carding machines . 11 5.5.1 General 71 5.5.2 Flat cards 13 5.5.3 Roller and clearer cards .. 5.5.4 Tape condensers... 14 5.6 Converters and stretch-breaking converters 15 5.7 Spinning preparation machines subsequent to carding 16 5.7.1 General..... 16 5.7.2 Draw frames for short fibres. 18 5.7.3 Gill boxes, including "intersecting" and "chain-gill" types .. 18 5.7.4 19 5.7.5 Sliver and ribbon lap machines, lap formers ... 19 5.7.6 Cotton combers... 20 5.7.7 Rectilinear combs (for worsted yarn and flax yarn and similar). 20 5.7.8 Speedframes.... 21 5.7.9 High draft finishers. 22 5.7.10 Automatic sliver can-doffing units.. 22 5.8 Spinning machines 23 5.8.1 General.. 23 5.8.2 Ring spinning machines.. 23 5.8.3 Open-end spinning machines.. .24 5.8.4 Gill spinning machines..... 6 Verification of the safety requirements and/or measures . 7 Information concerning machine use.......... Bibliography Copyrght International Organizaion for standardizlon'ghts reserved ii se from IHS Not for Resal ISO 11111-2:2005(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeen non-governmental, in liaison with isO, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adoptedbythetechnicalcommitteesarecirculatedtothememberbodiesforvoting.Publicationasan International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. I