ISO INTERNATIONAL STANDARD 11064-7 First edition 2006-04-01 Ergonomic design of control centres - Part 7: Principles for the evaluation of control centres Conception ergonomique des centres de commande - Partie 7: Principes pour I'évaluation des centres de commande Reference number ISO 11064-7:2006(E) @ISO 2006 py IHS under ted without license from IHS Not for Resale ISO 11064-7:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF fle can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ?ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2006 - All rights reserved ted without licensefrom IHS Not for Resale ISO 11064-7:2006(E) Contents Page Foreword iv Introduction 1 Scope 2 Normative references 3 Terms and definitions 4 Requirements and recommendations for evaluation process 4.1 General verification and validation (V&V) issues. 4.2 Verification and validation plan.. 4.3 Verification and validation scope. 4.4 Verification and validation criteria. 4.5 Verification and validation input documents . 4.6 Verification and validation team...... 4.7 Verification and validation resources. 4.8 Verification and validation methods. 4.9 Verification and validation measures . 4.10 Verification and validation results Annex A (informative) Checklist for V&v evaluation process 0 Annex B (informative) Evaluation process 12 Annex C (informative) Evaluation (V&vV) methods, 16 Bibliography 20 Copyrght International Organizationforstadardizalon ghts reserved ii se from IHS Not for Resale ISO 11064-7:2006(E) Foreword Iso (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeer established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with isO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 11064-7 was prepared by Technical Committee ISO/TC 159, Ergonomics, Subcommittee SC 4, Ergonomics of human-system interaction. IsO 11064 consists of the following parts, under the general title Ergonomic design of control centres: Part 1: Principles for the design of control centres Part 2: Principles for the arrangement of control suites Part 3: Control room layout Part 4: Layout and dimensions of workstations Part 6: Environmental requirements for control centres Part 7: Principles