ISO INTERNATIONAL STANDARD 10972-5 First edition 2006-10-01 Cranes Reguirements for mechanisms Part 5: Bridge and gantry cranes Appareils de levage a charge suspendue Prescriptions pour les mecanismes- Partie 5: Ponts et portiques roulants Reference number ISO 10972-5:2006(E) ISO @ ISO 2006 ISO 10972-5:2006(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and instailed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the @ISO2006 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56 · CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax+ 4122749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland @ ISO 2006 - All rights reserved IS0 10972-5:2006(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (lsOmemberbodies).The workofpreparingInternationalStandardsisnormallycarriedoutthroughIso International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 10972-5 was prepared by Technical Committee ISO/TC 96, Cranes, Subcommittee SC 9, Bridge and gantry cranes. IsO 10972 consists of the following parts, under the general title Cranes Requirements for mechanisms Part 1: General Part3:Towercranes -Part 4: Jib cranes Part5:Bridgeandgantrycranes n'ahtsreserved ili Copvriaht International Oraanization for Standardizatior ISO 10972-5:2006(E) INTERNATIONAL STANDARD Cranes Requirements for mechanisms Part 5: Bridge and gantry cranes 1 Scope This part of isO 10972 establishes the particular requirements relating to mechanisms for bridge and gantry cranes, as defined in IsO 4306-1. The general requirements for mechanisms for cranes are given in ISO 10972-1. These particular requirements concern a) the general layout and design of mechanisms; b) the selection and/or design requirements of components; c) the instructions for manufacturing, mounting, installation and testing. excluded from this part of ISO 10972. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated (including any amendments) applies. ISO 4306-1, Cranes— Vocabulary-Part 1: General Iso 10245-5, Cranes - Limiting and indicating devices - Part 5: Overhead travelling and portal bridge cranes Iso 10972-1, Cranes —Requirements for mechanismsPart 1: General IsO 12210-1, Cranes — Anchoring devices for in-service and out-of-service conditions — Part 1: General IsO 12488-1, Cranes — Tolerances for wheels and travel and traversing tracks Part 1: General machines 3 Terms and definitions For the purposes of this document, the terms and definitions given in IsO 4306-1 apply ion'ahts reserved ISO 10972-5:2006(E) 4 Requirements 4.1 General design and layout 4.1.1 General The mechanisms shall mee