ISO INTERNATIONAL STANDARD 10360-3 First edition 2000-03-15 Geometrical Product Specifications (GPS) Acceptance and reverification tests for coordinate measuring machines (CMM) 一 Part 3: CMMs with the axis of a rotary table as the fourth axis Spécification géométrique des produits (GPS) - Essais de réception et de vérification periodique des machines a mesurer tridimensionnelles (MTT) Partie 3: MMT ayant I'axe de rotation d'un plateau tournant comme quatriemeaxe Reference number ISO 10360-3:2000(E) ISO @ ISO 2000 Not for Resale ISO 10360-3:2000(E) PDFdisclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISo Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by isO member bodies. In the unlikely event ?ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland @ Iso 2000 - All rights reserved ermittedwithoutlicense from IHS Not for Resale ISO 10360-3:2000(E) Contents Page Foreword. Introduction Scope 2 Normative references .. 3 Terms and definitions 4 Requirements for metrological characteristics 4.1 Error of indication... 4.2 Environmental conditions. 4.3 Rotary table .... 4.4 Stylus system.. 4.5 Operating conditions... 5 Acceptance test and reverification test.... 5.1 Principles..... 5.2 Measuring equipment. 5.3 Procedure... 5.4 Obtention of test results 6 Compliance with specifications 6.1 Acceptance test ... 6.2 Reverification test 7 Applications. 7.1 Acceptance test 7.2 Reverification test 7.3 Interim check... Annex A (informative) Interim check Annex B (informative) Relation to the GPS matrix model.... 10 Bibliography ... 12 ii d by IHS under lic ut license from IHS Not for Resale ISO 10360-3:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO memberbodies).The work ofpreparingInternational Standards is normally carried out throughISO technica committees. Each member body interested in a subject for which a technical committee has been established has liaison with IsO, also take part in the work. IsO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Attention is drawn to the possibility that some of the elements of this part of isO 10360 may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. International Standard ISO 10360-3 was prepared by Technical Committee ISO/TC 213, Dimensional and geometrical product specifications and verification. Acceptance and reverification tests for coordinate measuring machines (CMM): —Part 1:Vocabulary Part 2: CMMs used for measuring linear dimensions Part 3: CMMs with the axis of a rotary table as the fourth axis Part 4: CMMs used in scanning measuring mode —Part 5: CMMs using multiple stylus probing systems -