ISO INTERNATIONAL STANDARD 10303-513 First edition 2000-09-01 Industrial automation systems and integration Product data representation and exchange : Part 513: Application interpreted construct: Elementary boundary representation Systemes d'automatisation industrielle et integration-Représentation et échange de données de produits - Partie 513: Construction interpreétée d'application: Représentation des limites elementaires Reference number ISO 10303-513:2000(E) E( @ ISO 2000 Copyright International Organization for Standardization Not for Resale IS0 10303-513:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this area. Adobe is a trademarkof Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event ?ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.ch Printed in Switzerland CopyightinteratinalOorganization for Standardization @ ISO 2000 - All rights reserved mittedwithoutlicensefrom IHS Not for Resale ISO 10303-513:2000(E) Contents Page Scope 1 2 Normative references 2 3 Terms, definitions, and abbreviations 2 3.1 Terms defined in ISO 10303-1 3 3.2 Terms defined in ISO 10303-42 3 3.3 Terms defined in ISO 10303-202 3 3.4 Terms defined in ISO 10303-514 4 3.5 Other definitions 4 3.6 Abbreviations 4 EXPRESS short listing 4 4 4.1 Fundamental concepts and assumptions 6 4.2 aic_elementary_brep schema entity definition: elementary_brep_shape_representation 7 Annex A (normative) Short names of entities 12 Annex B (normative) Information object registration 13 B.1 Document identification 13 B.2 Schema identification 13 Annex C (informative) Computer-interpretable listings 14 Annex D (informative) EXPRESS-G diagrams 15 Annex E (informative) AIC conformance requirements and test purposes 20 E.1 AIC conformance requirements: elementary B-rep 20 E.2 Test purposes for elementary B-rep AIC 21 E.3 Abstract test cases for elementary B-rep 25 E.4 Contexts defined for test cases of elementary B-rep 41 Index 56 Figures Figure D.1 aic_elementary_boundary_representation EXPRESS-G diagram, page 1 of 4 . : 16 Figure D.2 aic_elementary_boundary_representation EXPRESS-G diagram, page 2 of 4 . 17 Figure D.3 aic_elementary_boundary_representation EXPRESS-G diagram, page 3 of 4 . 18 Figure D.4 aic_elementary_boundary_representation EXPRESS-G diagram, page 4 of 4 19 Tables Table A.1 Short names of entities 12 c ISO 2000 All rights reserved ii from IHS Not for Resale IS0 10303-513:2000(E) Foreword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has theright to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaboratescloselywiththeInternationalElectrotechnicalCommission(lEC)onallmattersof electrotechnical standardization. International Standards are drafted in accordan