ISO INTERNATIONAL STANDARD 10303-505 First edition 2000-06-15 Industrial automation systems and integration Product data representation and exchange Part 505: Application interpreted construct: Drawing structure and administration Systemes d'automatisation industrielle et integration-Représentation et échange de donneées de produits - Partie 505: Construction interpreétée d'application: Structure et administrationdesdessins Reference number ISO 10303-505:2000(E) ISO @ ISO 2000 Not for Resale ISO 10303-505:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The IsO Central Secretariat accepts no liability in this area. Adobe is a trademarkof Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event ?ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland @Iso2000-All rights reserved ted without license from IHS Not for Resale ISO 10303-505:2000(E) Contents Page Scope 2 Normative references Terms, definitions and abbreviations 3.1 Terms defined in ISO 10209-1 . 3.2 Terms defined in ISO 10303-1 3.3 Terms defined in ISO 10303-46 . 3.4 Terms defined in ISO 10303-101 . 3.5 Terms defined in ISO 10303-202 3.6 Abbreviations . 4 EXPRESS short listing . 4.1 Fundamental concepts and assumptions ... 4.2 aic_drawing_structure_and_administration type definitions 4.3 aic_drawing_structure_and_administration entity definitions Annex A (normative) Short names of entities. .17 Annex B (normative) Information object registration.. B.1 Document identification . .18 B.2 Schema identification . .18 Annex C (informative) EXPRESS-G diagrar 19 Annex D (informative) Computer interpretable listings . Index 35 CopyrightInternaaganzaon for sandardizalionserved ii by IHS under lic from IHS Not for Resa ISO 10303-505:2000(E) Figures Figure C.1 - EXPRESS-G diagram 1 of 14 20 Figure C.2 - EXPRESS-G diagram 2 of 14 . .21 Figure C.3 - EXPRESS-G diagram 3 of 14 . 22 Figure C.4 - EXPRESS-G diagram 4 of 14 . 23 Figure C.5 - EXPRESS-G diagram 5 of 14 .. 24 Figure C.6 - EXPRESS-G diagram 6 of 14 25 Figure C.7 - EXPRESS-G diagram 7 of 14 . .26 Figure C.8 - EXPRESS-G diagram 8 of 14 . Figure C.9 - EXPRESS-G diagram 9 of 14 Figure C.10 - EXPRESS-G diagram 10 of 14 , 29 Figure C.11 - EXPRESS-G diagram 11 of 14 . .30 Figure C.12 - EXPRESS-G diagram 12 of 14 Figure C.13 - EXPRESS-G diagram 13 of 14 . 32 Figure C.14 - EXPRESS-G diagram 14 of 14 . Tables Table A.1 - Short names of entities .17 @IsO2000-All rights reserved ed without license from IHS Not for Resale ISO 10303-505:2000(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (isO member bodies). The work of preparing International Standards is normally carried out through ISO technical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEc Directives, Part 3 Draft International Standards adopted by the technical committees ar