ISO INTERNATIONAL STANDARD 10071-2 First edition 2005-08-01 Tools for pressing Ball-lock punches - Part 2: Ball-lock punches for heavy duty Outillage de pressePoincons a bille- Partie 2: Poincons a bille pour toles épaisses Reference number ISO 10071-2:2005(E) @ ISO 2005 Copyright International Organization for Standardization ted without license from IHS Not for Resale ISO 10071-2:2005(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by IsO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below ?ISO2005 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, IsO's member body in the country of the requester. ISO copyright office Case postale 56 . CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland Copyightinteratinal organization for Standardization @ ISO 2005 - All rights reserved nitted without licensefrom IHS Not for Resale ISO 10071-2:2005(E) Contents Page Foreword iv 1 Scope 2 Normative references 3 Terms and definitions... 4 Dimensions... 4.1 Basic dimensions Ball in locking position. 4.2 Perforating punches... 4.3 Pilots Types C and D... 4.4 Punches with ejector... 5 Material and hardness 10 6 Designation .10 Bibliography Copyrght International Organizaion forstandardizalon ghts reserved ii d by IHS uno ense with without license from IHS Not for Resale ISO 10071-2:2005(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technicalcommittees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeer established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with isO, also take part in the work. iso collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/lEC Directives, Part 2. adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 10071-2 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This first edition of ISO 10071-2, together with ISO 10071-1:2001, cancels and replaces IsO 10071:1991, of whichitconstitutesatechnicalrevision. Part 1:Ball-lock punches for light duty Part 2: Ball-lock punches for heavy duty onal Organization for Standardizatior ISO 2005 - All rights reserved INTERNATIONAL STANDARD ISO 10071-2:2005(E) Tools for pressing Ball-lock punches - Part 2: Ball-lock punches for heavy duty 1 Scope This part of IsO 10071 specifies interchangeability dimensions and tolerances, in millimetres, for ball-lock punches for heavy duty. It is applicable to ball-lock punches with shank diameter sizes from 10 mm up to including 40 mm, in round, square, rectangular and oblong shapes, for punching holes in steel sheets