ISO INTERNATIONAL STANDARD 1007 Third edition 2000-06-01 Photography 135-size film and magazine Specifications Photographie — Film et cartouche de format 135 - Spécifications Reference number ISO 1007:2000(E) ISO @ ISO 2000 ISO 1007:2000(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this area. Adobeis atrademarkof AdobeSystems Incorporated Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by isO member bodies. In the unlikely event @ISO2000 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56. CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 734 10 79 E-mail [email protected] Web www.iso.ch Printed in Switzerland ii @ IsO 2000 - All rights reserved ISO 1007:2000(E) Contents Page 1 Scope 2 Normative references. 3 Terms and definitions 4 Conditionsformeasurementofdimensions 5 Film cutting and perforation dimensions 6 Latent-image frame numbering 7 Latent-image digital bar-codes 8 Magazine dimensions. 20 6 Magazine bar-code 22 10 Camera auto-sensing areas. 24 11 Magazine information panel 12 Process identification 29 13 Film pull-out force 29 14 Film-spool attachment strength.. Annex A (normative) Assignment of DX numbers. Annex B (informative) Methods for measurement of key characteristics Annex C (informative) Historical dimensions used to design magazines and cameras .. 37 Bibliography. Figures Figure 1 135-size film and latent-image bar codes .. Figure 2 — Perforations for 135-size film (see Table 2) 8 Figure 3 — 135-size magazine bar-code (see Table 8). 9 Figure 4 — 135-size film magazine (see Table 7) . .20 Figure 5 — 135-size camera auto-sensing areas (see Table 10). 25 Figure 6 — 135-size magazine information panel (see Table 14) 29 Figure B.1 Dc electrical circuit for camera auto-sensing testing . .35 Figure C.1 Magazine design aims. 37 Tables Table 2 Dimensions for cutting and perforating 135-size film (see Figure 2). 8 @ ISO 2000 - All rights reserved ili ISO 1007:2000(E) Table 3 Latent-image bar-code identification array: Part 1 DX numbers . Table 4 Latent-image bar-code identification array: Part 2 DX numbers 13 Table 5 Latent-image bar-code identification array: Dual-track frame-number codes. 15 Table 6 - Latent-image bar-code identification array: Single-track frame-number codes .. Table 7 Dimensions of 135-size film magazine (see Figure 4).. 21 Table 8 Dimensions of 135-size magazine bar-code (see Figure 3).. 23 Table 9 - Magazine bar-code: Assignment for number of exposures (digit 6)... ..24 Table 10 Dimensions of 135-size camera auto-sensing areas (see Figure 5).. 26 Table 11 Auto-sensing areas: Code for Iso speed/exposure index 27 Table 12 Auto-sensing areas: Code for number of exposures. .28 Table 13 Auto-sensing areas: Code for exposure latitude Table 14 Dimensions of 135-size magazine information panel (see Figure 6). 29 iv @ ISO 2000 - All rights reserved ISO 1007:2000(E) Foreword ISsO (the International Organization for Standardization) is a worldwide federation of national standards bodies (sO memberbodies).The workof preparingInternationalStandardsisnormallycarried outthroughISOtechnica committees.Eachmemberbodyinterestedinasubjectforwhichatechnicalcommitteehasbeenestablishedhas the right to be represented on that committee. International organizations,