ISO INTERNATIONAL STANDARD 366-3 Second edition 2009-03-01 Textilemachineryandaccessories Reeds - Part 3: Dimensions and designation of metal reeds with double-spring baulk Materielpourl'industrietextile-Peignes- Partie 3:Dimensions et designation des peignesmetalliques a ligature double Reference number ISO 366-3:2009(E) @ISO 2009 ISO366-3:2009(E) PDF disclaimer This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The IsO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHTPROTECTEDDOCUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any fom or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either IsO at the address below or ISO's member body in the country of the requester. ISO copyright office Case postale 56.CH-1211Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail [email protected] Web www.iso.org Published in Switzerland ii @ ISO 2009 All rights reserved ISO366-3:2009(E) Contents Page Foreword.. 1 Scope 2 Dimensions. 3 Designation @ Iso 2009 -All rights reserved ii ISO366-3:2009(E) Foreword IsO (the International Organization for Standardization) is a worldwide federation of national standards bodies technical committees. Each member body interested in a subject for which a technical committee has been InternationalElectrotechnicalCommission(lEC)onallmattersofelectrotechnicalstandardization. International Standards are drafted in accordance with the rules given in the IsO/lEC Directives, Part 2 adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. rights. IsO shall not be held responsible for identifying any or all such patent rights. ISO 366-3 was prepared by Technical Committee ISO/TC 72, Textile machinery and accessories, Subcommittee Sc 3, Machinery forfabric manufacturing including preparatory machineryand accessories. This second edition cancels and replaces the first edition (Iso 366-3:1988), which has been technically revised. Iso 366 consists of the following parts, under the general title Textile machinery and accessories-Reeds: Part1:Pitch bound reeds—Dimensions Part 2:Dimensions anddesignation of metalreedswithplatebaulk Part3:Dimensionsanddesignation of metalreeds with double-springbaulk Part4:Dimensionsanddesignationofplastic-boundmetalreeds Part5:Dimensionsanddesignationofprofilecapsules iv @ ISO 2009 - All rights reserved ISO 366-3:2009(E) INTERNATIONALSTANDARD Textile machinery and accessories Reeds Part 3: Dimensions and designation of metal reeds with double-spring baulk 1 Scope This part of isO 366 specifies the dimensions and designation of metal reeds with double-spring baulk for weaving machines. 2 Dimensions The dimensions of metal reeds with double-spring baulk shown in Figure 1 and given in Table 1, and the Designation The designation of metal reeds with double-spring baulk shall include the following information in the order given: a) "Metal reed with double-spring baulk"; b) reference to this part of ISO 366, i.e.ISO 366-3; c) inner height of the reed, e, in millimetres; overall height of the reed, hg, in millimetres; e) thickness of the reed baulk, d, in millimetres; f) width of the dents of the reed, b, in millimetres; (6 type of steel used for the dents of the reed, i.e. plain or stainless. EXAMPLE A